android: 修正增强档位说明（写反了）+ 分析页测温点沿用照片数值

上一提交把档位含义写成了「越高纳入越多弱对比区域」，方向是反的。按公式
amplitude = strength*(center-mean)/divisor, divisor = max(max-mean, mean-min, mapStrength),
mapStrength = strength*gain*2>>8 重新推导：
- 弱对比区域 divisor 被 mapStrength 兜住 → 幅度 = 128/gain，与档位无关；
- 强边缘 divisor 由对比度主导 → 幅度随档位线性增长；
- 门槛 mapStrength <= range*32 → 档位越高弱对比区域被整个排除（正是噪声所在处）。
即高档位是「更锐但更挑」。设置页文案与 DetailEnhance 文档已改正，
并加 theLevelRaisesTheContrastGateAndDropsWeakDetail 锁定
（range=60 窗口：8 档 mapStrength 1500 通过、16 档 3000 被拒）。
真机 HF 实测 0.365(关) / 0.438(6档) / 0.433(8档)，与推导一致。

分析页测温点原先前先重新测量 NUC，于是照片上烧录的 Pt2 26.1℃ 与面板 25.9℃
不一致（与极值同一类漂移）。现在优先用文件记录的 tempMc——照片上印的就是它，
仅在记录缺失时才测量。真机确认照片/面板/极值三方数值完全一致。

真机（小米 22041211AC/Android12/MIUI，重启后冷启动）：15.1fps 稳定、单帧 6.1~6.6ms、
6/8 档 9.9~10.3ms、拍照 extremes=2、分析页只有一个 min/max 且与照片重合、
底部面板可见（36.0/20.4/24.5）。101 项测试全绿。

android/app/src/main/kotlin/com/mag160c/thermal/core/DetailEnhance.kt

@@ -44,6 +44,18 @@ package com.mag160c.thermal.core
  * near-silent on flat areas). The divisor floor is what keeps flat, noisy regions
  * quiet while edges still get pushed.
  *
+ * ## What the strength level actually controls
+ *
+ * Raising the level does two things at once:
+ *   1. it RAISES the contrast gate — a window is enhanced only when its 7x7 range
+ *      clears `mapStrength / 32`, so low-contrast areas (where sensor noise lives)
+ *      are excluded entirely at high levels; and
+ *   2. it RAISES the amplitude on strong edges, where the local contrast itself
+ *      dominates the divisor.
+ * Where the contrast is small enough that the divisor floor applies, the amplitude
+ * works out to `strength / mapStrength` = `128 / gain` — independent of the level.
+ * That is why turning the level up sharpens the picture instead of boiling it.
+ *
  * ## Validation status — READ THIS
  *
  * The arithmetic above is a faithful transcription, and the structural properties

android/app/src/main/kotlin/com/mag160c/thermal/ui/analyze/AnalyzeViewModel.kt

@@ -102,8 +102,15 @@ class AnalyzeViewModel(
             // which showed up on device as two "min" markers a few pixels apart.
             if (recorded.minPos >= 0) mnPos = recorded.minPos
             if (recorded.maxPos >= 0) mxPos = recorded.maxPos
+            // Each probe keeps the temperature the CAPTURE recorded, because that is
+            // the number burned into the photo next to the marker. Re-measuring the
+            // NUC block gives a slightly different value (the sensor drifts between
+            // capture and reload), which showed on device as the photo saying
+            // "Pt2 26.1" while the panel said 25.9 for the same point. Only probes
+            // that somehow lack a recorded value are measured.
             val loaded = (parsed?.probes.orEmpty()).map { p ->
-                Probe(p.x, p.y, p.label, measureSensor(p.x, p.y) ?: (p.tempMc / 1000f))
+                Probe(p.x, p.y, p.label, (p.tempMc / 1000f).takeIf { p.tempMc != 0 }
+                    ?: measureSensor(p.x, p.y) ?: 0f)
             }
             withContext(Dispatchers.Main) {
                 _render.value = bmp

android/app/src/main/kotlin/com/mag160c/thermal/ui/settings/SettingsScreen.kt

@@ -247,17 +247,21 @@ fun SettingsScreen(
             text = {
                 Column {
                     Text(
-                        "加强局部细节（官方同款 7×7 局部映射）。档位沿用官方 SDK 自己的" +
-                            "定义：档位越高，纳入增强的弱对比区域越多（边缘强度本身不变），" +
-                            "画面更通透，弱细节里的噪声也会一起显现。",
+                        "加强局部细节（官方同款 7×7 局部映射）。档位越高：①对比度门槛越高，" +
+                            "只有更强的细节会被增强，弱对比区域（噪声所在处）被排除；" +
+                            "②强边缘的增强幅度更大。所以高档位是「更锐但更挑」，" +
+                            "而不是「连噪声一起放大」。",
                         style = MaterialTheme.typography.bodySmall,
                         color = MaterialTheme.colorScheme.onSurfaceVariant,
                         modifier = Modifier.padding(bottom = 8.dp),
                     )
                     // Vendor levels: MAG_SetDetailEnhancement accepts 0..32 and the
-                    // pipeline uses `level << 3`. Extra headroom is safe because the
-                    // per-edge amplitude is level-independent (128/gain); the level
-                    // only decides which windows clear the contrast threshold.
+                    // pipeline uses `level << 3`. The level raises BOTH the contrast
+                    // gate (a window qualifies only when its 7x7 range clears
+                    // mapStrength/32) and the amplitude on strong edges (where the
+                    // local contrast dominates the divisor). On flat, noisy areas the
+                    // divisor floor holds the amplitude at 128/gain regardless of
+                    // level, which is why cranking it up sharpens instead of boiling.
                     Column(
                         modifier = Modifier
                             .heightIn(max = 320.dp)